Network questions

NAME: SONGA SHIN

Homework Assignment

Homework Assignment - Extra Credit for Mid Term 2 Exam.

The total credit for this will be ELEVEN points and these points will be added to your midterm examination grade.

This homework assignment is DO BY FRIDAY MAY 5 at 11:59 PM. There is no extension after that. If you do not have it in by then please do not contact me asking for an extension. Please do not wait until that evening to submit the assignment. If your network goes down, your computer freezes, Blackboard is offline, you cannot get on wireless, etc... there is NO EXTENSION. I highly recommend that you submit it earlier then Friday

This MUST BE submitted via Blackboard. I will not accept anything emailed to me. There is no exceptions to this.

To do this assignment download attached Word Document and fill it in. There is one topic per page and a few questions. On each page:

- Put you name on the top of each page

- Answer the questions

- Show a screenshot of the command (with the results of the command being issued)

If you cannot take a screenshot use your camera and take a picture of the screen and include that in the document.

If you do not put you name on the top of each page, answer all of the questions or include a screenshot the question will be marked wrong – There is NO partial credit. NO EXCEPTIONS

When you save the file and upload it please change the name of the file to include your name in it.

NAME:SONGA SHIN

Questions 1

  1. What is the IP Address of your computer?

  2. What command did you use to get it?

Screenshot is below

NAME: SONGA SHIN

Questions 2

  1. What is the MAC Address / Physical Address of your computer?

  2. What command did you use to get it?

Screenshot is below

NAME:SONGA SHIN

Questions 3

  1. What is your EXTERNAL Facing IP Address?

  2. This is NOT the same as question 1

How did you get it?

Screenshot is below

NAME:SONGA SHIN

Questions 4

  1. What command can you use to test connectivity between two hosts?

  2. What is shown when you test the connectivity to www.yahoo.com?

Screenshot is below

NAME:SONGA SHIN

Questions 5

  1. What command can you use to show the path a packet takes to get from your computer to another host?

  2. What is shown when you use this command to find the path to www.yahoo.com?

Screenshot is below

NAME:SONGA SHIN

Questions 6

  1. What command do you use to show all of the IP addresses that have been resolved to MAC addresses?

Screenshot is below

NAME:SONGA SHIN

Questions 7

  1. What command do you use to see:

  • The DNS Server you are using (Name)

  • The IP Address of the server

Screenshot is below

NAME:SONGA SHIN

Questions 8

  1. Using the same command from question 7

  2. What happens when you look up www.yahoo.com?

Describe what you are seeing in the output? When you look up www.yahoo.com there will be EIGHT lines (approximately) What dord each line represent (fill in below)

Screenshot is below

NAME:SONGA SHIN

Questions 9

  1. What command do you use to see if the IP addressing you are using DHCP?

  2. This same command can be used to see how long the lease is for the IP address? What is the start and end of your lease period?

  3. What is the DHCP Server IP Address?

Screenshot is below

NAME:SONGA SHIN

Questions 10

  1. What command do you use to see network connections?

  2. How would you modify the command to see statistics about inbound and outbound traffic?

TWO Screenshots are below (one for each of the questions above)

NAME:SONGA SHIN

Question 11

The following three questions are not for a specific command, switch or parameter? For the below three questions I am NOT looking for examples of commands, switches or parameter. I am looking for the general definitions of the word “command”, “switch” and “parameter”

  1. What is a Command?

  2. What is a switch?

  3. What is a parameter?

Issue any command with a parameter and a switch

The following six questions ARE for the specific command, switch and parameter that you chose.

  1. What was the command you used?

  2. What does the command do?

  3. What was the parameter you used?

  4. What did the parameter do?

  5. What was the switch you used?

  6. What did that switch do?

Screenshot of the command with the parameter and switch being used