Answered You can buy a ready-made answer or pick a professional tutor to order an original one.

QUESTION

this is a university physic 2 lab i think it is simple. please read the both attachment. Building the Circuit 1. Open the circuit simulator by going to the following website: http://falstad.com/circui

this is a university physic 2 lab i think it is simple. please read the both attachment.

Building the Circuit

1. Open the circuit simulator by going to the following website: http://falstad.com/circuit/.

A sample circuit is running when the page opens.

2. Click the Circuits pulldown menu then hover over the Basics submenu. Click Capacitor.

This will automatically load our basic RC circuit.

3. Right click on the resistor and choose Edit. This will allow you to set the resistance. For

now, set the resistance to 10 kΩ by typing ‘10k’ into the textbox.

4. Right click on the capacitor and choose Edit. Set the capacitance to 330 F. The ‘u’

notation in the textbox indicates ‘micro’.

5. Right click on the Battery and choose Edit. Set the Voltage to 4.5 V.

6. The graph at the bottom of the screen is the “Scope” and displays the voltage across the

capacitor in green and the current in the circuit in yellow. You will notice that to the right

of the graph is a time value and that time is passing but very slowly. You can alter the

flow of time here by adjusting the red and grey slider in the upper right of the screen

labelled Simulation Speed. You can also pause the flow of time entirely by clicking the

Run/Stop button.

Page 5

Data Collection

1. Charge the capacitor by closing the switch to the left such that the Capacitor charges

through the Resistor. Let the capacitor charge until the voltage across it is at least 4

volts. You can adjust the simulation speed.

2. Move the switch to the right position so that the Capacitor discharges through the

Resistor. If you sped up the simulation speed, you may want to slow it back down and

be ready to push the Run/Stop button.

3. When the voltage across the capacitor reaches 3 volts, record the value for t found to

the right of the Scope Display in Table 1.

4. When the voltage reaches 1.5 volts, stop the watch and record the value for t in Table

1. Calculate and record the measured time of the half-life, h in Table 1 as h = tf - ti.

5. Calculate and record the measured time constantC of the RC circuit in Table 1 as C =

h / ln(2).

6. Calculate and record both the theoretical time constant and theoretical half-life of the

circuit using C = RC and h = C ln(2). Record these values in Table 1.

7. Calculate and record the percent error in your experimental value of the time constant

and half-life for this combination of capacitor and resistor. Given that this is a

simulation, the percent error should be extremely low. Record these in Table 1.

8. Right click on the Resistor and choose Edit. Set the resistance to 22 kΩ and repeat

steps 1 – 7. Record all results in Table 2.

9. Right click on the Resistor and choose Edit. Set the resistance to 10 kΩ. Right click

on the Capacitor and choose Edit. Set the capacitance to 1000 µF. Repeat steps 1-7

and record all results in Table 3.

10. Right click on the Capacitor and choose Edit. Set the capacitance to 2200 µF and

repeat steps 1 – 7. Record all results in Table 4.

11. Right click on the Resistor and choose Edit. Set the resistance to 22 kΩ and repeat

steps 1 – 7. Record all results in Tab

Show more
knjukievans
knjukievans
  • @
  • 190 orders completed
ANSWER

Tutor has posted answer for $50.00. See answer's preview

$50.00

******** ******

Click here to download attached files: PHYS 2426- The RC Circuit - Report Template 000.xlsx
or Buy custom answer
LEARN MORE EFFECTIVELY AND GET BETTER GRADES!
Ask a Question