Answered You can hire a professional tutor to get the answer.
This questions are due on 11/25/15, and all about my project.
ET1310Project PROJECT: AMPLIFIER PROJECTProject Introduction:In this project, you will develop an amplifier application using one of the BJT or FET amplifiers that werecovered in this course. You will submit the project in two parts, Part 1 in Module 3 and Part 2 in Module 6. In Part 1, you will submit the project proposal along with the first draft of the circuit schematic and designconsiderations to the instructor for feedback. Your instructor will provide feedback by the beginning ofModule 4. Part 2 of the project begins with implementing your instructor feedback. Based on the feedback,you will revise the circuit schematic; compose components list; provide data sheets for all components usedin the amplifier design; and provide updated calculations, schematic diagrams, component list, data sheetand Multisim analysis for the amplifier design. In case there is a delayed or no feedback from the instructor,you are suggested to continue work on Project Part 2. Course Learning Objectives Covered:3. Describe the basic construction and operation of bipolar junction transistors (BJTs) and identifyvarious types of BJT transistor package configurations.4. Determine the range of BJT transistor circuit V-I operating points for each BJT biasing circuit andexplain how a transistor can be used as a switch.5. Describe and analyze the operations of common-emitter, common-collector, and common-baseamplifiers.6. Troubleshoot power supply failures and faults in transistor circuits using accepted techniques.7. Describe the construction classifications and operations of field-effect transistors (FETs) and identifyvarious types of FET transistor package configurations. 1 ET1310Project PROJECT SUBMISSION P LANProject Description/Requirements of Project Part Part Evaluation Criteria Project Assessment Preparation Checklist: The Project rubric will Part 1 To prepare for Project Part 1, review the readings and lessons be used to evaluate for Modules 1 through 3. this assessment. Your Title: Amplifier Project submission will be Research the ITT Tech Virtual Library and other credible Web evaluated against the resources to come up with a proposed idea for the amplifier following criteria application you intend to use in this project. In a Microsoft using the grading Word document, describe the amplifier application that you rubric: have selected. The final proposal should give just an overview of Did the project the amplifier application. In your description, make sure to cite proposal include the sources in APA format. original designideas? The proposal needs to be reviewed and approved by your Did the project instructor. In case there is a delayed or no feedback from the proposal provide instructor, you are suggested to continue work on Project Part a brief overview 2. of the amplifier Submission Requirements: application? Submit a written proposal of the following specification: Did the project Font: Arial; font size: 12; double-spaced proposal Length: 2–3 pages adequately cite Citation Style: APA the resourcesused? Due: Module 3Grading Weight: 5% 2 ET1310Project Project Description/Requirements of Project Part Part Evaluation Criteria Project Assessment Preparation Checklist: The Project rubric will Part 2 To prepare for Project Part 2, review the readings and lessons be used to evaluate for Modules 4 through 6. this assessment. Your Title: Amplifier Project submission will be Begin Project Part 2 by implementing the feedback received evaluated against the from your instructor on your proposed amplifier application following criteria draft. In case there is a delayed or no feedback from the using the grading instructor, you are suggested to continue work on Project Part 2 rubric: using the same draft that you submitted. Did theamplifierperform Perform the following tasks: Design and develop an amplifier application. properly with Research the ITT Tech Virtual Library and other credible no errors? Web sources to help you in the design and Were theamplifier development of the amplifier application. calculationsaccurately Your Project Part 2 submission must include the following:Amplifier Design Specifications: The amplifier design shown in the must include all DC and AC parameters, gain, input report? resistance, and output resistance calculations covered Did the in this course. A biasing circuit and any additionalcomponents used to interface with the application are Working Model of the Amplifier Application: Using componentsand amplifier design. equipment Report Submission: Write a report documenting design with all considerations and calculations, schematic diagrams, 3 all Multisim, demonstrate a working version of your diagram show also part of the design. schematic components ET1310Project Project Description/Requirements of Project Part Part Evaluation Criteria component list, data sheets, results, and conclusions. appropriatelylabeled? In addition, answer the following questions in the report:o Were datasheets provided for efficiency? all design What changes would you make on your current components design to reduce the cost of production?o identified and design to improve amplifier performance and o What changes would you make on your current in the report? What are some real-world industry applications for which your design can be used? Were clearresults of the PowerPoint Presentation: Create a PowerPoint working presentation describing the details of your design. This system presentation should summarize the information provided in presented in your written report and should be no more the report? than 15 slides in length. Were the Submission Requirements: conclusions Submit the following files to your instructor: clearly and completely specifications. A Word document explaining the amplifier design stated in the A multisim file that demonstrates the working version report? of your simplifier design. Did the A Word document documenting design considerations. PowerPoint A PowerPoint presentation summarizing the presentation information presented in the written report. use goodgraphics and Due: Module 6Grading Weight: 10% 4 PowerPointthemes? ET1310Project ProjectPart Description/Requirements of Project Part Evaluation Criteria Did thePowerPointpresentationclearlydescribe thedesignincluding alldesignfeatures? 5
